Making Scented Soy Pillar Candles

Printer friendly instructions for soy candle making

These instructions are specifically for scented soy pillar candles made using candle molds. A little more challenging to make than soy container candles, they're elegant, subtly fragranced and environmentally friendly.

Cover your work surface with a protective covering such as newspaper, wax paper or a plastic tablecloth. Wear clothes it's okay to mess up. Have some rags or paper towel ready to mop up any spills.

Make sure you have all your equipment set up within easy reach. Click here for a complete list of soy candle making supplies.

Scented Soy Pillar Candles
STEP 1: Prepare your mold

1. You may want to start by spraying the inside of the mold with a releasant, especially if you're making a large candle, to make it easier to slide the pillar out of the mold. It's not always necessary for smaller candles, but once you're making larger scented soy candles, it comes in handy!




2. Cut a length of candle wick about twice as long as the height of your candle mold.



3. Thread your wick through the wick-hole in the base of the mold.



Handy Hint: If you can't thread the wick through the hole because the wick is frayed, dip one end in some hot wax, then roll it with your fingers to form a point.


4. Set the wick in place. There are several options for this.

   ... Use a tapered rubber plug. Fasten the wick to the top of the mold (see step 5) pull tight at the base and push the small end of the rubber plug into hole at base of your mold.

   ... Use a tapered rubber plug. Pull the wick tight at the base and push the small end of the rubber plug into hole at base of your mold.

   ... Use mold sealing putty. Here's how: first, make absolutely sure the bottom of your candle mold is perfectly clean. If it's not, the sealing putty will let go of the mold when you pour in the hot wax.

   Pull the wick taut and cut it about 1 inch past the base of the mold, then coil the wick into a spiral. If you want, you can use a piece of masking tape to hold it in place while you prep your sealing putty.

   Use your fingers to shape a piece of sealing putty into a flat disc big enough to cover the wick spiral (and the masking tape if you use it.) Press the putty firmly into place, making sure it completely covers the wick... or you'll end up with a big mess!

Scented Soy Pillar Candles
STEP 2: Heat the wax

1. Melt the soy wax chips (or block - just cut a chunk off) in a double boiler. If you don't have a double boiler, use a candle pouring pot (or a large, clean coffee can) in a pot with about 1" of water.

   Use a large metal or wooden spoon to stir the wax as you go along - it speeds up the melting process. You can also add more soy wax as it melts down if you think you'll need more to fill your mold.

   Use a candy thermometer to measure the temperature.



2. When the wax reaches 180F and is completely melted, add dye (if you're using it. Note: you need A LOT of dye to achieve a deep color - be generous!) Stir well.



3. Let wax cool to about 140F, then add your essential oil blend. Stir some more.

Scented Soy Pillar Candles
STEP 3: Pour the wax

1. Pour the wax into your mold up to about half an inch (1.25cm) from the top. Save about a cup of wax to re-pour the candle later.



2. Let the candle cool a bit until a surface has formed on the top. Use a skewer or chopstick to poke holes down through the wax, stopping about an inch from the bottom. This is to provide vents through which the wax can suck air as it shrinks and hardens. (Shrinkage is completely normal.)

   Relief holes are important: Without them you can end up with air cavities in the candle, the wick can be pulled off-center, or the candle can become deformed. Not good!



3. Re-poke your relief holes a few times as the candle cools to make sure the vent stays clear.



4. Let your candle cool overnight in the mold.



5. Re-melt your reserved soy wax, heating to 180F. Pour the wax into your candle, not going above the original fill line. Overfilling may cause wax to seep down between the mold and the candle (not good.)



6. Let the candle cool completely.

Scented Soy Pillar Candles
STEP 4: Release the candle

1. Remove the wick sealer (foam/washer, rubber plug or wick screw) from the bottom of the mold. Your candle should now slide out of the mold. If not, put it in the fridge for about 15 minutes, then try again. This helps the wax shrink even more to separate it from the mold.



2. The wick bar/pencil/chopstick end of the candle is the bottom of the candle. Use scissors to trim this end of the wick flush with the base of the candle.



3. You might want to level the base of the candle. Put a cookie sheet (one with sides works best) on top of a pot of boiling water. Put the candle on the cookie sheet and use the heated sheet to melt away some of the wax until you have a flat base.



4. Trim the top wick to about 1/4" (0.5cm)

Instructions for Soy Container Candles

Essential Oil Blends for Soy Wax Scented Candles

Soy Candle Making Supplies

Soy Candle Making Tips

Go to Aromatherapy Recipes Homepage from Scented Soy Pillar Candles